Skip to content
Secured Engineers Pvt. Ltd. logo
Design & Coordination

What Does an MEP Consultant Do? Scope of Work and Deliverables by Stage

13 November 2026 · 6 min read · by

Title card reading What Does an MEP Consultant Do? Scope of Work and Deliverables by Stage

An MEP consultant designs the mechanical, electrical, plumbing and fire systems of a building and then checks that they are built as designed. The consultant works for the owner, not the installer: it sets the design basis, sizes every system, writes the specifications and bill of quantities, reviews the contractor's drawings, and witnesses the tests before handover.

What an MEP consultant is responsible for

The consultant is the design authority for building services. Four disciplines sit under that heading:

  • Mechanical: heating, ventilation and air conditioning, process cooling, exhaust and pressurisation.
  • Electrical: HT and LT distribution, transformers and DG sets, panels, cabling, earthing, lighting and lightning protection.
  • Plumbing and public health: water supply, drainage, storage, pumping, rainwater, sewage and effluent treatment.
  • Fire protection: detection and alarm, hydrants, sprinklers, pump rooms and the fire water tank.

In India fire protection is a separate statutory approval, which is why many briefs say MEPF rather than MEP. The consultant designs to the National Building Code, the state fire rules, the electricity supply code and the DISCOM's connection conditions, and the design must survive the Fire NOC and CEIG inspections at the end. What MEPF means

A consultant does not supply or install anything. It also does not normally run the site day to day. Those are the contractor's jobs, which is why the two roles are compared below.

Scope of work by stage

Most Indian MEP appointments follow five stages. The table shows what the consultant does at each one and what you should receive before it is paid for.

StageWhat the consultant doesWhat you should receive
Concept and design basisReads the architectural and structural intent, fixes the design criteria, estimates loads and space needsDesign basis report, load summaries, plant-room and shaft area schedule, utility requirement letter
Tender packageDevelops each system to tender level, writes specifications, measures quantities, sets the exclusionsTender drawings, specifications, bill of quantities, approved makes list, tender clarifications
Good-for-construction drawingsCoordinates services with structure and architecture, resolves clashes, freezes the designGFC drawings with revision codes, schedules, single-line diagrams, cable and pipe sizing calculations
Construction stageReviews shop drawings and material submittals, answers site queries, inspects at agreed hold pointsSubmittal review log, site observation reports, non-conformance notes, test witnessing records
HandoverChecks commissioning results, as-built drawings and O&M documents against the designCommissioning review, as-built acceptance, snag list, statutory approval support record

The stage names match our fee guide, which sets out what the design fee should cover at each stage, so the two documents can be read together when you compare proposals.

Deliverables you should insist on

A proposal that only lists "drawings" is not a scope. Ask for each of these by name:

  1. Design basis report. The occupancy, indoor conditions, diversity factors, redundancy and codes the design follows. Every later argument about capacity goes back to this document.
  2. Load calculations. Electrical demand and maximum demand, cooling load, water demand and fire water demand, each with its assumptions shown.
  3. Single-line diagrams and schematics. Electrical SLD, HVAC schematic, water and drainage schematics, fire hydrant and sprinkler schematics.
  4. Specifications and approved makes. Written to a standard, not to a brand, with the makes listed separately.
  5. Bill of quantities. Measured, itemised, with an exclusions sheet, so bidders price the same thing. What a tender BOQ must close off
  6. Coordinated GFC drawings. With a revision register, so the site builds the latest set and nobody builds from a superseded one.
  7. Review records. Shop drawing comments, material approvals, inspection reports and test witnessing records, dated and signed.
  8. Handover review. A note confirming that the as-built drawings, test certificates and O&M manuals match what was designed and installed.

Where a consultant's scope usually stops

Scope gaps cost more than fees. These items are commonly outside a standard appointment unless you add them:

  • Full-time site supervision. Most consultants visit at hold points. Daily supervision is a separate appointment or a project management role.
  • Statutory liaison. Preparing the technical documents for the Fire NOC, CEIG and DISCOM applications is usually included; running the applications and attending inspections may be priced separately. Ask.
  • Architectural and structural design. The consultant coordinates with these designers but does not produce their drawings.
  • Procurement. The consultant recommends makes and reviews offers; it does not buy.
  • BIM and clash reports. Valuable on tight buildings, but a separate deliverable with its own level of detail.
  • Energy modelling and green-building documentation. Normally priced as an add-on.
  • Redesign after a change in brief. A change in built-up area, occupancy or phasing is new work.

Write the exclusions into the appointment letter in the same way you would in a construction contract. Scope gaps that turn into claims

MEP consultant vs MEP contractor: who does what

The consultant decides what is to be built and checks it. The contractor builds it, tests it and hands it over with records. On an item-rate or lump-sum project you appoint both separately, and the consultant's review protects you against the contractor's substitutions. On a design-and-build or turnkey project one firm carries both roles under a single contract, which removes the gap between design and site but means you should ask for an independent review of the design basis and the handover tests.

Secured Engineers works as an MEP contractor and consultant, so a project can take either route. Our guide to what an MEP contractor does covers the contractor side in the same stage structure.

How the fee is usually structured

Three structures are common in India: a percentage of the MEP works cost, a rate per square foot or square metre of built-up area, and a lump sum broken down by stage. Each has a different incentive. A percentage fee rises with the cost of the works it is meant to control; an area rate ignores complexity; a stage lump sum is the easiest to compare and to pay against deliverables. Typically the fee is released stage by stage against the documents in the table above. We do not publish a fee because it depends on the building type, the number of systems and the construction-stage involvement you want.

What to send for a useful first conversation

A consultant can give you a scope and fee proposal quickly if the enquiry carries:

  • the site location and the type of building or plant, with the built-up area and number of floors;
  • the architectural drawings available, even at concept level;
  • the sanctioned or expected electrical load and the DISCOM;
  • the process loads, if any, and the hours of operation;
  • the approvals already in hand, such as the building plan sanction;
  • the target dates for tender, construction start and occupation.

The MEPF cost calculator gives a budget range from the area and building type, which is a useful sense check before any proposal arrives.

How Secured Engineers helps

Secured Engineers Pvt. Ltd. is an MEP contractor and consultant with offices in Noida and Ludhiana. Design is done in-house, and the statutory applications that follow the design, including Fire NOC, CEIG and DISCOM net-metering, are filed in-house. Consultancy can be appointed on its own through our design and approvals service, or combined with execution so that MEPF and solar run under one contract. The company has delivered 535+ projects across 18+ states, with 89.77% repeat clients. Overseas project teams use the same engineering desk through our remote MEP consultancy.

If you have a drawing set and want to know what a consultant's scope should cover for it, send it for a scope and fee proposal through the enquiry form, on WhatsApp at +91 70099 85817, or by calling the same number.

Frequently asked

What does an MEP consultant do on a project?

An MEP consultant sets the design basis for the mechanical, electrical, plumbing and fire systems, sizes each system, produces the drawings, specifications and bill of quantities for tender, coordinates the services with the structure, reviews the contractor's shop drawings and submittals, and witnesses tests before handover. The consultant works for the owner and does not supply or install equipment.

Does a small factory need an MEP consultant?

A small unit with a simple LT connection and no fire hydrant requirement may manage with a competent contractor's design. Once the project needs a Fire NOC, an HT connection, a CEIG inspection or process cooling, an independent design basis and a measured BOQ usually save more than the fee, because they stop over-sizing and scope disputes before the award.

Does the MEP consultant obtain the Fire NOC and CEIG approval?

The consultant prepares the technical drawings and calculations the applications depend on. Whether it also files the applications, attends inspections and closes observations depends on the appointment. Ask for the approvals scope in writing. Secured Engineers files these approvals in-house when the consultancy includes them.

What is the difference between an MEP consultant and an MEP contractor?

The consultant designs and checks; the contractor supplies, installs, tests and hands over. On a design-and-build or turnkey project one firm does both under a single contract. Secured Engineers works as a contractor and consultant, so the roles can be separate or combined depending on how you want to allocate risk.

How long does MEP design take?

It depends on the stage of the architectural design, the number of systems and how quickly decisions are made. The design basis can be fixed early from concept drawings; the tender package needs a frozen architectural layout; GFC drawings need the structural drawings. Agree a programme with hold points for each stage rather than a single end date.

Related services

Share the coordinated layouts or clash reports you have — an engineer reviews the services zones and where they conflict.

Services not fitting the drawings?

Tell us about your project — our engineers respond within one business day.

  • ★ 4.7 (239 Google reviews)
  • 535+ projects
  • Reply in 1 business day

Tells us which channels bring real projects. “I don’t remember” is a fine answer.

Add details (optional — company, email, scope and site address)

🔒 Your details go straight to our team. No spam, ever.

Ready to start your project?

Get a free consultation and quote. We design, prepare and file your approvals, and execute — you deal with one team.

ONE PARTNER. END TO END. You focus on your business — we handle the rest.
Quality Safety Commitment
Speak to a Lead Engineer